Wood Stove HES350

Wood Stoves Ventis

▪Extra-large wood stove on pedestal
▪EPA certified at only 1.6 g/h
▪Solidity and manufacturing quality
▪C-Cast heat shield added to the firestop ▪Non-catalytic combustion technology
▪Installation authorized on the Island of Montreal
▪Cast iron door
▪Top heat deflector and side panels

Appliance performance

Fuel type Dry cordwood (16″ recommended)
Recommended heating area (9) 1,000 – 2,700 ft²
Overall firebox volume 3.5 ft³
EPA loading volume 2.88 ft³
Maximum burn time (9) 10 h
Maximum heat output-dry cordwood (4) 110,000 BTU/h
Minimum overall heat output rate (4) (5) 17,200 BTU/h (5.0 kW)
Maximum overall heat output rate (4) (5) 57,800 BTU/h (16.9 kW)
Average overall efficiency-dry cordwood (HHV) (5) (6) 71 %
Average overall efficiency-dry cordwood (LHV) (5) (7) 76 %
Optimum efficiency (1) (2) 77 %
Optimum heat transfer efficiency (8) 75 %
Average particulate emission rate (3) 1.6 g/h
Average CO (10) 73 g/h
1. Performances based on a fuel load prescribed by the standard at 7 lb/ft³ and with a moisture content between 19% and 25%.
2. Optimum overall efficiency at a specific burn rate (LHV).
3. This appliance is officially tested and certified by an independent agency.
4. The maximum heat output (dry cordwood) is based on a loading density varying between 15 lb/ft³ and 20 lb/ft³. Other performances are based on a fuel load prescribed by the standard. The specified loading density varies between 7 lb/ft³ and 12 lb/ft³. The moisture content is between 19% and 25%.
5. As measured per CSA B415.1-10 stack loss method.
6. Higher Heating Value of the fuel.
7. Lower Heating Value of the fuel.
8. The optimum heat transfer efficiency is for the low burn rate (using HHV) and represents the appliance’s ability to convert the energy contained in the solid fuels into energy transferred to the room in the form of heat and does not take into account the chemical losses during combustion.
9. Recommended heating area and maximum burn time may vary subject to location in home, chimney draft,heat loss factors, climate, fuel type and other variables. The recommended heated area for a given appliance is defined by the manufacturer as its capacity to maintain a minimum acceptable temperature in the designated area in case of a power failure.
10. Carbon monoxyde.

General Features

Alcove installation approved Yes
Mobile home approved Yes, with fresh air intake
Certified according to applicable standards CAN/USA accredited laboratory
Overall dimension (Width) 28 3/4″
Overall dimension (Height) 34 3/4″
Overall dimension (Depth) 30 5/8″
Premium quality blower included (CFM) Optional
Combustion technology Non-catalytic
Stainless-steel secondary-air system Yes
Flue outlet diameter 6″
Recommended chimney diameter 6″
Type of chimney CAN/ULC S629, UL 103 HT (2100 °F)
Minimum chimney height 12′
Door type Single, glass with cast iron frame
Door opening size (Width) 19″
Door opening size (Height) 9 1/4″
Glass type Ceramic glass
Glass surface – W x H 18 3/8″ x 11 1/2″
Steel thickness-body 3/16″
Steel thickness-top 5/16″
Firebox size (Width) 22 7/8″
Firebox size (Height) 12 3/4″
Firebox size (Depth) 20 1/8″
Log positioning Loading over width and over depth
Maximum log length 22″
Firebox lined with refractory bricks Yes
Baffle type High quality vermiculite
High-efficiency certified appliance Yes, EPA 2020 certified
Canadian Standard (emissions) CSA B415.1-10
USA Standard (emissions) EPA
Canadian Standard (safety) ULC S627
USA Standard (safety) UL 1482, UL 737
Warranty Limited lifetime

Clearances

Minimum clearances to combustibles*
(Data expressed in inches. 1 inch = 25.4 mm)